DESCRIPTION
Waspaloy® is a nickel-based, age hardenable superalloy with great strength at temperatures up to 1600°F. The alloy’s chemistry allows for age hardening that surpasses the performance of alloy 718 for demanding, high temperature applications. Waspaloy® can withstand combustion environments due to excellent resistance to relaxation at elevated temperatures, combined with appreciable oxidation resistance. The alloy also maintains considerable resistance to fatigue in these applications.
Applicable Specifications
Strip and Foil:
AMS 5544
Applications
Gas Turbine Components, Seals, Springs, Fasteners
Industries Supplied
Military and Commercial Aerospace, Land-Based Gas Turbines, Automotive
Nominal Composition
C: 0.02 max
Mn: 1.00 max
Si: 0.75 max
P: 0.030 max
S: 0.030 max
Cr: 18.0 – 21.0
Co: 12.0 – 15.0
M0: 3.5 – 5.0
Al: 1.20 – 1.60
B: 0.003 – 0.010
Zr: 0.02 – 0.12
Cu: 0.50 max
Ni:58 bal
Ti: 2.75 – 3.25
Fe: 2.0 max
Physical Properties
Density:
0.296 lb/in3, (8.19 g/cm3)
Modulus of Elasticity (E):
At 70°F (20°C): 30.9 x 103 ksi (213 GPa)
Coefficient of Expansion:
7.7 µin/in.-°F (70-1000°F)
14.3 µm/m-°C (20-600°C)
Electrical Resistivity:
0.37 µohm-ft, (1.20 µohm-m)
Thermal Conductivity:
125 Btu-in/ft2hr-°F, (1000°F)
19.1 W/m-°C (600°C)
Typical Mechanical Properties
Annealed
- Heat Treatment: 1825-1925°F (995-1080°C)
Or per specifications - Tensile Strength: 160 ksi max (1100 MPa)
- Suggested Operating Conditions: -300 to 1600°F (-184°C to 871°C)
Annealed + Aged
- Heat Treatment: Stabilization 1550°F (845°C)
Age 1400°F (760°C)
Or per specifications - Tensile Strength: 170 ksi max (1100 MPa)
- Suggested Operating Conditions: Up to 1020°F (549°C)
Low stress up to 1400°F (760°C)
Spring Temper
- Heat Treatment: None
- Tensile Strength: 200 ksi max (1380 MPa)
- Suggested Operating Conditions: Up to 1020°F (549°C)
Low stress up to 1400°F (760°C)
Waspaloy® is a registered trademark of United Technologies Corp.
For further information Contact:
CONTACT US
Phone: 1.888.843.2350
Elgiloy Specialty Metals – Strip Products
1565 Fleetwood Dr
Elgin, IL 60123 USA
Limitation of Liability and Disclaimer of Warranty:
- The content in these data sheets is provided primarily by third-party melting mills and is provided for reference only. It is not intended for engineering or design.
- Applications may be discussed, however, Elgiloy Specialty Metals, a Division of Combined Metals Company LLC, does not recommend or endorse any material for any particular end use or application.
- The data included in this data sheet are typical values and may vary.
- Elgiloy Specialty Metals, a Division of Combined Metals Company LLC, makes no representations or warranties, express or implied, as to the accuracy, completeness, condition, suitability, performance, fitness for a particular purpose, or merchantability of any information contained in any data sheet.
In no event will Elgiloy Specialty Metals, a Division of Combined Metals Company LLC, be liable for any damages whatsoever arising from the use of the information included in the data sheets.
