STRIP - Alloy 316/316L Stainless Steel
UNS S31600/S31603
W.Nr 1.4401/1.4404
DESCRIPTION
Type 316 is an austenitic chromium-nickel-stainless steel containing molybdenum. This addition increases general corrosion resistance, improves resistance to pitting from chloride ion solutions, and provides increased strength at elevated temperatures. Properties are similar to those of Type 304/304L except that this alloy is somewhat stronger at elevated temperatures. Corrosion resistance is improved, particularly against sulfuric, hydrochloric, acetic, formic and tartaric acids; acid sulfates and alkaline chlorides. Type 316L is an extra-low carbon version of Type 316 that minimizes harmful carbide precipitation during welding.
Applicable Specifications
Strip and Foil:
AMS 5907, AMS 5524, ASTM F899, ASTM A666, NACE MR0175/ISO 15156
Applications
Exhaust manifolds, Furnace parts, Heat exchangers, Jet engine parts, Pharmaceutical and photographic equipment, Valve and pump trim, Tubing, Chemical equipment, Digesters, Tanks, Evaporators, Paper and textile processing equipment, Food processing equipment, and Marine parts.
Industries Supplied
Aerospace, Chemical Processing, Food Processing, Power Generation, General Manufacturing
Nominal Composition
C: 0.07 max
Mn: 2.00 max
Si: 1.00 max
P: 0.045 max
S: 0.030 max
Cr: 16.5 – 18.0
Ni: 10.5 – 13.5
N: 0.10 max
Mo: 2.00 – 2.50
Fe: Balance
Physical Properties
Density:
0.285 lb/in3, (8.00 g/cm3)
Modulus of Elasticity (E):
At 70°F (20°C): 28.0 x 103 ksi (193 GPa)
Modulus of Rigidity (G)
At 70°F (20°C): 10.1 x 103 ksi (70 GPa)
Coefficient of Expansion:
9.2 µin/in.-°F (70-212°F)
16.6 µm/m-°C (200-100°C)
Electrical Resistivity:
29.1 µohm-in, (74 µohm-cm)
Thermal Conductivity:
9.4 Btu-in/ft2hr-°F, (212°F)
16.2 W/m-°C (100°C)
Typical Mechanical Properties
Annealed
- Heat Treatment: 1900-2050°F (1038-1121°C)
- Tensile Strength: 75 – 105 ksi (515-725 MPa)
- Suggested Operating Conditions: -200°F to 1700°F (-184°C to 927°C)
1/4 Hard
- Heat Treatment: (Stress relieve 600-900°F as needed)
- Tensile Strength: 125 ksi min (860 MPa)
- Suggested Operating Conditions: -200°F to 550°F (-184°C to 288°C)
1/2 Hard
- Heat Treatment: (Stress relieve 600-900°F as needed)
- Tensile Strength: 150 ksi min (1030 MPa)
- Suggested Operating Conditions: -200°F to 550°F (-184°C to 288°C)
Spring Temper
- Heat Treatment: (Stress relieve 600-900°F as needed)
- Tensile Strength: 185 ksi min (1275 MPa)
- Suggested Operating Conditions: -200°F to 550°F (-184°C to 288°C)
For further information Contact:
CONTACT US
Phone: 1.888.843.2350
Elgiloy Specialty Metals – Strip Products
1565 Fleetwood Dr
Elgin, IL 60123 USA
Limitation of Liability and Disclaimer of Warranty:
- The content in these data sheets is provided primarily by third-party melting mills and is provided for reference only. It is not intended for engineering or design.
- Applications may be discussed, however, Elgiloy Specialty Metals, a Division of Combined Metals Company LLC, does not recommend or endorse any material for any particular end use or application.
- The data included in this data sheet are typical values and may vary.
- Elgiloy Specialty Metals, a Division of Combined Metals Company LLC, makes no representations or warranties, express or implied, as to the accuracy, completeness, condition, suitability, performance, fitness for a particular purpose, or merchantability of any information contained in any data sheet.
In no event will Elgiloy Specialty Metals, a Division of Combined Metals Company LLC, be liable for any damages whatsoever arising from the use of the information included in the data sheets.
